Site principal franēais English main page Deutsche Hauptseite 

 

motrona: control-motion-interface       
     control  -  motion  -  interface


 

Home
Welcome to motrona

About motrona
Company and Contact Persons

International
Distributors Worldwide

Support
Brochures-Documents-Software

Contact
How to contact motrona

control

Panel Meters, Indicators

Electronic Counters

Tachometers, Frequency Meters

Timers, Industrial Stopwatches

SSI Indicators, Parallel Displays

PROFIBUS / CANBUS Indicators

Speed and Motion Monitors

motion

Synchronization of Drives

“Flying” Saw and Shear Control

Rotating Cross Cutter Control

Rotary Eccentric Shear Control

Tubular Bag Machine Control

Winding and Traverse Control

Printing and Punching Control

interface

Signal Converters Frequency >>

Signal Converters Analogue >>

Signal Converters SSI and Parallel >>

Signal Converters Incremental >>

Level Converters TTL-RS422-HTL

Encoder Distributors,  Splitters

Frequency Dividers, Multipliers

Interface for SinCos Encoders

Combinations with Converters

Accessories

Controllers for Rotating Cross Cutters (Paper, Corrugated Board etc.),
for Rotating Punchers and other Rotary Operations

* = instant stock availibility

Rotary  Cut-to-Length Control

      ______________________________________________________________________

    New universal Motion-Controller MC800 with an integrated tandem drive-controller, flexible input configuration for sensors and adaptive interface structure. With firmware CT803 suitable for rotating processes.

    The Multi-Axes-Motion-Controller MC800, a successor of the proven MC700, is convincing by its higher bandwidth and a more flexible bus architecture. A  special feature of the MC800 is the integrated tandem drive-controller. This enables to reach the acceleration requirements of  heavy loads by splitting the necessary power to two independent drives.

  • Suitable for incremental encoders or sensors with RS422 output or 10 to 30 V HTL output (differential signals A, /A, B, /B)
  • Freely combined with standard SinCos sensors or SinCos encoders with 1 Vpp (format sin+, sin-, cos+, cos-)
  • Four fast interrupt based HTL NPN/PNP inputs for control commands
  • Two 14 bit analogue inputs with  ±10 V, as well as two similar analogue outputs
  • OnBoard interfaces: Ethernet TCP/IP, CANOpen, Modbus RTU, RS232/RS485 interface
  • Optional interfaces: e.g. Profinet, EtherCAT, Profibus DP, DeviceNet etc.
  • Snap-on module for standard DIN rails (35 mm C-profile)
     
  • Synchronous process during penetration of the tool and length dependent speed outside this phase
  • Optimizing polynomial speed profile to ensure extremely smooth motion and gentle tool treatment for best service life
  • High cutting precision, even at high line speeds, due to a max. 2 MHz feed-back frequency of the incremental input or 1 MHz of the SinCos input
  • High dynamic response by means of short cycle time (300 µse), therefore accurate cutting results also during change of line speed
  • Suitable to operation with all 4-quadrant drives providing a standardized drive communication bus (e.g. SerCos II) or a ±10 V speed input
  • Easy setup and commissioning by use of the Windows based operating software (freeware), resulting in successful machine operation within shortest time
  • The controller can communicate with external operation terminals as well as HMI via standardized factory communication bus (e.g. Profinet)
     

Motion Controller for Rotary Cutters with Tandem Function

      ______________________________________________________________________

    Motion-Controller MC700* with Firmware CT703* for
    Rotating Cross Cutters and other Rotary Operations

  • MC700 is a universal motion controller for 1 to 4 axis, programmable for multiple motion applications by simple download of the corresponding function firmware.
  • With use of the CT703 firmware (see SUPPORT) this unit provides excellent solutions with all kinds of rotating cut-to-length systems as well as with applications like rotary labeling, printing, punching, sealing etc.
  • Functions and properties are very similar to the CT340 controllers described below.
  • The range of functions includes extended possibilities with evaluation and blanking of print marks, floating print mark registers and more
  • The MC700 hardware is a black-box unit for cabinet mounting.
    Remote control and communication facilities via external operator terminal, serial PC communication, CANBUS,  PROFIBUS etc. (see also Accessories)

Motion Controller for Rotary Cutters

      ______________________________________________________________________

    CT340 * /CT641: Compact and Low Priced Motion Controller
    for Rotative Machining, Rotating Cross Cutters, Rotary Punchers and Other Intermittent Operations

  • New stand-alone precision controller for the specific motion profile of rotative cutting or printing rolls, e.g. for cut-to length or intermittent printing of paper, corrugated board and synthetic materials
  • Also most suitable for smaller machines with limited budget, due to a very competitive price
  • Speed profile with synchronous operation during tool engagement and asynchronous speed while the tool is free, automatically optimized to the actual length setting
  • Self-optimizing polynomial speed profile to ensure extremely smooth motion and gentle tool treatment for best service life
  • High accuracy and repeatability, even with high line speeds, due to a 300 kHz frequency range of the incremental encoder inputs
  • Continuous closed-loop position control with only 250 µsec of cycle time, therefore outstanding dynamic features and high precision even during changes of the line speed
  • Suitable for operation with all 4-quadrant drives providing a +/- 10V  speed input
  • Instantly ready for use, with easy setup and commissioning via Windows PC software (freeware), resulting in successful machine operation within shortest time
  • The controller can be operated by means of control keys or thumbwheel switches on the front side, as well as by remote operation terminals or by serial link
  • Direct PROFIBUS access is possible with use of gateway model PB251
    (see Accessories)
  • Compact DIN housing for front panel mounting
  • Optional assembly to DIN rails with use of the mounting supports SM300/ SM600 (see Accessories)
Controller for Rotating Cross Cutters CT340 Controller for Rotating Cross Cutters CT641

 

 

 

 

________________________________________________________________________________________________________________________________________________________________
[Legal Notice]                          [webmaster@motrona.com]                       © 2014 motrona GmbH, Zwischen den Wegen 32, 78239 Rielasingen (Germany)              September, 2014