Accessories for motrona Products
|
|
* = instant stock availability
|
ES001*: Incremental Encoder Simulator
|
|
- Testing unit for generation of all typical encoder output signals
- Outputs A, /A, B, /B, Z, /Z with any level between 5 and 30 volts
- Output frequency adjustable from 0 to 500 kHz
- Marker pulse output with programmable distance
- Selectable direction of rotation (phase A/B)
- Indexing mode for generation of a fixed number of output pulses in multiples of 1, 10, 100 and 1000 pulses
- Suitable best for testing of cables and wiring in a machine, for “dry run” with the machine in standstill, for multiple operational testing and
setup of counters, meters and converters needing incremental input signals
|
|
|
|
PB251*: PROFIBUS-to-Serial Converter (Gateway)
|
|
- Low cost and high performance gateway for easy connection of motrona units to a PROFIBUS network (DPV1)
- Small and compact housing for DIN rail mounting
- DIL switches for setting of communication profile
- Power supply 18-30 VDD
- applicable with all motrona indicators, counters, controllers and converters providing a serial RS232 link
|
|
|
|
RV210: Communication Splitter RS485 <==> 4 x RS232
|
[PDF manual]
|
- Splitter for serial communication between one RS485 Master device and
four RS232 Slave units
|
|
|
|
BT348: Mini Operator Terminal
|
|
- Simple low-cost terminal for entry of single parameters and read-out of settings or actual values
- Suitable for all motrona controllers and other motrona units providing serial communication
- Also applicable as an additional remote display (on-site indicator), when the same value has to be indicated on several places at the same
time
|
|
|
|
Touchscreen HMI Terminals:
- For operation with motrona controllers, many standard HMI terminals are available on the market
- The following products provide very easy setup when used with motrona products, because the motrona communication protocol as described
under [SERPRO] is already installed. Both units are
universal HMI Touchscreen Devices with 2 serial ports, for simultaneous and integrated operation with motrona controllers and PC / PLC
controls,
- For some cut-to-length applications motrona can supply HMI firmware with complete screen masks and operator screens (available on
request)e
BT600 (Red Lion)
TFT-Touch-Display 480 x 272 pixels, Front Dimensions 120 x 96 mm
(4.725 x 3.78’’), 2 independent serial interfaces
BT700 (Hitech)
TFT-Touch-Display 640 x 480 pixels, Front Dimensions 187 x 137 mm
(7.36 x 5.39’’), 2 independent serial interfaces
|
|
|
|
NT 215*: Universal Power Unit 24 VDC / 15 W (Lambda)
- Wide-band input range 85 - 264 VAC (50 - 60 Hz) or 90 - 375 VDC
- Output 24 VDC (+/-1%), 630 mA, 15 watts
- Dimensions 22,8 x 75 x 96,7 mm (0.9 x 2.95 x 3.81 ‘‘)
- Particularly suitable for supply of all motrona units needing a 24 volts DC power supply
|
|
|
|
RL203: Relay PCB with two standard relays
RL204: Relay PCB with two safety relays (forced guided contacts)
|
|
- Suitable for use with all motrona units providing transistor switching outputs
- Each relay with 2 dry changeover contacts for 230 VAC / 2 A or 24 VDC / 3 A
- RL203 provides 2 standard PCB relays type Omron G2R-2
- RL204 provides 2 safety relays type Elesta SIR 282 with forced guided contacts
- PCB with plastic frame for DIN rail mounting
|
|
|
|
Mounting Clamps and Brackets
SM 300*: Angle support with
brackets, for DIN rail mounting of indicators and display units with front dimensions 96 x 48 mm
SM 600*: Angle support with brackets,
for DIN rail mounting of indicators and display units with front dimensions 96 x 96 mm
|
|
|
|
TG 300: Desktop Housing
This table housing is suitable for all units with front dimensions
96 x 48 mm (3.78 x 1.89’’)
|
|
|
|
Assembled Cables:
SK 232*:
Serial RS 232 cable for connection between PC and motrona control units.
One connector Sub-D-9 (male) and one connector Sub-D-9 (female), cable lengths 3 meters (approx. 10 feet).
FK 470*:
Ribbon cable for easy cascading of two encoder spitters type GV470 (mounted
side-by-side). Sub-D-9 connectors (male) on both sides, length 10 cm (3.94 ‘’).
|
|
|
|
Sub-D-Connectors (without cable)
DS 009*: Sub-D-connector
9-position (male), solder connection, metallised plastic enclosure, including mounting screws
DB 009*: Sub-D-connector
9-position (female), solder connection, metallised plastic enclosure, including mounting screws
DS 025*: Sub-D-connector
25-position (male), solder connection, metallised plastic enclosure, including mounting screws
DB 025*: Sub-D-connector
25-position (female), solder connection, metallised plastic enclosure, including mounting screws
|
|
|
|
VTxxx: Protective Caps and Plexiglas Bonnets
To increase the protection class with dusty or wet environment, several types of protection caps are
available for motrona units.
Some of the elastic and transparent plastic caps allow to operate the
keypad or to set the thumbwheel switches behind the cap, without removing it.
|
|
